ELAFLEX Configurator Hose Assemblies

1

0

Yellow Band

Additional Info

Yellow Band

Fuelling hoses for petroleum based products, aircraft and marine fuelling hoses.
Lining: NBR

2

0

Economy

Additional Info

Economy

Fuelling hoses for petroleum based products, simplified economy version.
Lining: NBR

3

0

Slimline

Additional Info

Slimline

Petrol pump hoses according to EN 1360 and EN 13483. For gasoline and diesel fuels.
Lining: NBR

4

0

Orange Band (LPG)

Additional Info

Orange Band (LPG)

LPG hoses according to EN 1762 for propane, butane, and their mixtures. Type LPG 16 also for AdBlue. Lining: NBR

5

0

Lilac Band (CHD / CHS)

Additional Info

Lilac Band (CHD / CHS)

Chemical hoses according to EN 12115 for over 75% of all industrial chemicals.
Lining: EPDM

6

0

Blue Band (LMD / LMS)

Additional Info

Blue Band (LMD / LMS)

Solvent hoses according to EN 12115 for solvents, paints and other mediums.
Lining: NBR 2

7

0

Universal Hoses (UPE)

Additional Info

Universal Hoses (UPE)

Universal hoses according to EN 12115 for almost all chemical and petroleum based products.
Lining: UPE

8

0

Universal Hoses (FEP / PTFE)

Additional Info

Universal Hoses (FEP / PTFE)

Universal hoses according to EN 12115 for almost all mediums.
Lining: FEP / PTFE

9

0

Special Hoses

Additional Info

Special Hoses

Special hoses for foodstuffs, ammoniac, hot air, cement, hot asphalt, steam and hot water.

10

0

PAL Quality Hoses

Additional Info

PAL Quality Hoses

PAL hoses (ex 'Paguag') for the chemical industry.

11

0

ELAPHARM^® / ElaSil Pharma

Additional Info

ELAPHARM^® / ElaSil Pharma

Hose assemblies for pharmaceutical biotechnology industry.
Lining: PTFE, FDA-conform or silicone platinum cured

12

0

'FWS' Composite Hoses

Additional Info

'FWS' Composite Hoses

Multi-layer thermoplastic hoses according to EN 13765. Delivery as checked hose assembly.
Lining: PP / PTFE / PA (6 types)

13

0

High Pressure Fuelling Hose (without helix)

'Yellow Band' high pressure fuelling hose without helix for reel operation. Ideal for all petroleum based products. Temperature range -30° up to +90° C (temporarily up to +110° C). Electrical conductivity <10⁶ Ohm. Corresponds to EN 1761. Can be calibrated according to European regulations. Approved acc. to German military standard VG 95 955 Typ D. Corresponds to EN 12115.

DN 10 to DN 100

'Yellow Band' high pressure fuelling hose without helix for reel operation. Ideal for all petroleum based products. Temperature range -30° up to +90° C (temporarily up to +110° C). Electrical conductivity <10⁶ Ohm. Corresponds to EN 1761. Can be calibrated according to European regulations. Approved acc. to German military standard VG 95 955 Typ D. Corresponds to EN 12115.

14

0

Fuel Oil Reel Hose (without helix)

Economy fuel oil reel hose without helix for petroleum based products. Temperature range -30° up to +70° C. Electrical conductivity <10⁶ Ohm.

DN 25 to DN 75

Economy fuel oil reel hose without helix for petroleum based products. Temperature range -30° up to +70° C. Electrical conductivity <10⁶ Ohm.

15

0

Tank Truck Hose (with steel helix)

'Yellow Band' smooth bore tank truck hose with kink resistant steel helix for all petroleum based products with an aromatic content up to 50%. Temperature range -30° up to +90° Celsius. Electrical conductivity <10⁶ Ohm. Approved to German military standard VG 95 955 type S. Complies with EN 12115 and EN 1761.Type STW = reinforced TW design. Particularly suitable as marine bunker hose (details see catalogue page 129).

DN 19 to DN 200

'Yellow Band' smooth bore tank truck hose with kink resistant steel helix for all petroleum based products with an aromatic content up to 50%. Temperature range -30° up to +90° Celsius. Electrical conductivity <10⁶ Ohm. Approved to German military standard VG 95 955 type S. Complies with EN 12115 and EN 1761.Type STW = reinforced TW design. Particularly suitable as marine bunker hose (details see catalogue page 129).

16

0

Light Weight Tank Truck Hose (with steel helix)

'Yellow Band' light weight tank truck hose with smooth bore and with corrugated cover. Easy to handle due to high flexibility, with double helix. Same material, range of application and the yellow bands as type TW.

DN 50 to DN 100

'Yellow Band' light weight tank truck hose with smooth bore and with corrugated cover. Easy to handle due to high flexibility, with double helix. Same material, range of application and the yellow bands as type TW.

17

0

Tank Truck Hose (with steel helix)

'Economy' tank truck hose, with steel helix, for petroleum based products. Temperature range -30° up to +70° C. Electrical conductivity <10⁶ Ohm. Corresponds to EN 1761.

DN 25 to DN 100

'Economy' tank truck hose, with steel helix, for petroleum based products. Temperature range -30° up to +70° C. Electrical conductivity <10⁶ Ohm. Corresponds to EN 1761.

18

0

Lightweight Gravity Discharge
Road Tanker Hose Type 'LG'

Elaflex provides a new solution for fuel delivery to petrol stations: Type 'LG' Lightweight Gravity Discharge road tanker hoses.The easy to handle rubber hose has been developed for pressureless service, to fill underground storage tanks. At a glance: excellent flexibility – also in winter operation, low weight, high flowrate due to smooth bore, robust, suitable for tough continuous operation.

DN 50, DN 75, DN 100

Elaflex provides a new solution for fuel delivery to petrol stations: Type 'LG' Lightweight Gravity Discharge road tanker hoses.The easy to handle rubber hose has been developed for pressureless service, to fill underground storage tanks. At a glance: excellent flexibility – also in winter operation, low weight, high flowrate due to smooth bore, robust, suitable for tough continuous operation.

19

0

Vapour Recovery Hose (with steel helix)

Type GPS is a flexible, lightweight hose for Stage 1B balanced vapour recovery (during the unloading of road tankers into the storage tank).For the assembling, clamp type SPANNLOC or SPANNFIX fittings can be used. If the steel helix is connected at both ends, GPS is suitable for electronic filling cross-over-prevention systems.Designed for 10 bar working pressure with safety factor of 4. Temperature range -30° up to +90° C.

DN 50

Type GPS is a flexible, lightweight hose for Stage 1B balanced vapour recovery (during the unloading of road tankers into the storage tank).For the assembling, clamp type SPANNLOC or SPANNFIX fittings can be used. If the steel helix is connected at both ends, GPS is suitable for electronic filling cross-over-prevention systems.Designed for 10 bar working pressure with safety factor of 4. Temperature range -30° up to +90° C.

20

0

Aircraft Refueling Hose (without helix)

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

DN 10 to DN 100

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

21

0

Aviation Refuelling Hose (without helix)

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

DN 38 to DN 100

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

22

0

Aviation Refuelling Hose (with plastic helix)

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

DN 38 to DN 75

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

23

0

Aviation Refuelling Hose (with steel helix)

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

DN 25 to DN 100

'Yellow Band' aircraft refuelling hoses, suitable for all aviation gasolines and jet fuels (JET A 1), deicing fluids and motor oils. Temperature range -30° up to +90° Celsius. Electrical resistance between 10³ and 10⁶ Ohm.

24

0

Petrol Pump Hoses
black or coloured

SLIMLINE quality petrol pump hoses for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B30 (BIO Type up to B100).
Meets weights and measures regulations, see page 111b.
Cold flexible down to -30° C/-22° F (LT-type down to -40° C/ -40° F), temp. up to +55° C/ +131° F.

Correspond to EN 1360, respectively EN 13483.

DN 16 to DN 21

SLIMLINE quality petrol pump hoses for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B30 (BIO Type up to B100).
Meets weights and measures regulations, see page 111b.
Cold flexible down to -30° C/-22° F (LT-type down to -40° C/ -40° F), temp. up to +55° C/ +131° F.

Correspond to EN 1360, respectively EN 13483.

25

0

Type Slimline 'SL LT'

Slimline SL LT

Additional Info

Add to compare

Type Slimline 'SL LT'

Petrol Pump Hoses
Low Temperature, black or coloured

Type Slimline 'SL LT': Special low temperature type for use in cold climate regions. Good flexibility down to -40° Celsius.

Type SL 25 LT: Suitable for cold and warm regions. Good flexibility down to -40° Celsius.

SLIMLINE quality petrol pump hoses for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B30 (BIO Type up to B100).
Meets weights and measures regulations, see overleaf.

Correspond to EN 1360, respectively EN 13483.

DN 16 to DN 25

Type Slimline 'SL LT': Special low temperature type for use in cold climate regions. Good flexibility down to -40° Celsius.

Type SL 25 LT: Suitable for cold and warm regions. Good flexibility down to -40° Celsius.

SLIMLINE quality petrol pump hoses for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B30 (BIO Type up to B100).
Meets weights and measures regulations, see overleaf.

Correspond to EN 1360, respectively EN 13483.

26

0

Petrol Pump Hoses,
for gasoline and diesel fuels, black or coloured

Type 'SL BIO': Special type for Biodiesel (HVO) up to B 100 to EN 14214. Also suitable for Diesel.
Meets weights and measures regulations, see overleaf. Cold flexible down to -30° C/-22° F (LT-type down to -40° C/-40° F).

Correspond to EN 1360, respectively EN 13483.

DN 16 to DN 25

Type 'SL BIO': Special type for Biodiesel (HVO) up to B 100 to EN 14214. Also suitable for Diesel.
Meets weights and measures regulations, see overleaf. Cold flexible down to -30° C/-22° F (LT-type down to -40° C/-40° F).

Correspond to EN 1360, respectively EN 13483.

27

0

COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, black or coloured

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

DN 21

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

Product Name	Type COAX
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Size	DN 21
Product Sheet	GR 11

28

0

COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, Low Temperature, black or coloured

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

DN 21

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

Product Name	Type COAX LT
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, Low Temperature, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Size	DN 21
Product Sheet	GR 11

29

0

Economy (without helix)

Type 'LC-Mix' is a light petrol pump hose for industrial / agricultural dispensers, motor scooter
dispensers and electric barrel pumps.

DN 13 to DN 25

Type 'LC-Mix' is a light petrol pump hose for industrial / agricultural dispensers, motor scooter
dispensers and electric barrel pumps.

30

0

Type Slimline 'SL SF'

Slimline 'SL SF'

Additional Info

Add to compare

Type Slimline 'SL SF'

Petrol Pump Hoses
Sulpur Free, black or coloured

Quality petrol pump hoses SLIMLINE SF, sulphur-free special type. Suitable for gasoline and diesel fuels, also with ethanol content up to E 85 and Biodiesel up to B 30. Meets weights and measures regulations, see page 111b. Cold flexible down to -30° C / -22° F (LT-type down to -40° C / -40° F), up to +55° C / +131°F.

Correspond to EN 1360 and EN 13483.

DN 16 to DN 21

Quality petrol pump hoses SLIMLINE SF, sulphur-free special type. Suitable for gasoline and diesel fuels, also with ethanol content up to E 85 and Biodiesel up to B 30. Meets weights and measures regulations, see page 111b. Cold flexible down to -30° C / -22° F (LT-type down to -40° C / -40° F), up to +55° C / +131°F.

Correspond to EN 1360 and EN 13483.

31

0

Type Slimline 'SL SF LT'

Slimline 'SL SF LT'

Additional Info

Add to compare

Type Slimline 'SL SF LT'

Petrol Pump Hoses
Low Temperature, Sulphur Free, black or coloured

Type Slimline 'SF LT': Special low temperature and sulphur-free type for use in cold climate regions. Good flexibility down to -40° Celsius.

DN 16 to DN 21

Type Slimline 'SF LT': Special low temperature and sulphur-free type for use in cold climate regions. Good flexibility down to -40° Celsius.

32

0

COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, Sulpur Free, black or coloured

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

DN 21

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

Product Name	Type COAX SF
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, Sulpur Free, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Application	For the operation in particularly cold regions (e.g. Scandinavia), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Comment	Refineries and Oil companies spend considerable effort in fulfilling the maximum allowed sulphur content of 10 mg/kg (corresponding 10 ppm) of the EN 228 and EN 590 fuel standards.To support these endeavours, Elaflex introduced a new special type of hose where rubber compounds are free of sulphur: Type Slimline 'SL SF'.• Tests of fuel samples verified that the sulphur content of the fuel is not increased, even if the medium remains for a long time within the hose. • It fulfills all requirements of the relevant hose standards. Properties are equally good or even better than those of standard Slimline hoses.
Size	DN 21
Product Sheet	GR 11

33

0

COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, Low Temperature, Sulphur Free, black or coloured

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

DN 21

PETROL PUMP HOSE (outside)
TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm.
Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands.
Cover: chlorinated synthetic rubber, resistant to light cracks.
Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85.

HOSE COUPLINGS (factory assembled)
Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard
thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM).
Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT
(Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm.
Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi.

ANTI-KINKING SLEEVE
On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane.
With degassing holes. Non-reusable.

COLOUR SLEEVE
Short sleeve CS 21 with stable colours for grade identification or company colours.
Made of polyurethane with smooth glossy surface in all known company colours.
Retrofitting and disassembly are possible (see page GR 13).

VAPOUR HOSE (inside)
Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible).
Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending
radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black,
with non reusable stainless steel clamps.
Nozzle side with arresting device through locked vapour hose tail.
Pump side swivel supported to avoid twisting through torsion.

COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION
According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %.

PERMEABILITY
According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard.

LOW TEMPERATURE BENDING FORCE
The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.

Product Name	Type COAX SF LT
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, Low Temperature, Sulphur Free, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Application	For the operation in particularly cold regions (e.g. Scandinavia), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Comment	Refineries and Oil companies spend considerable effort in fulfilling the maximum allowed sulphur content of 10 mg/kg (corresponding 10 ppm) of the EN 228 and EN 590 fuel standards.To support these endeavours, Elaflex introduced a new special type of hose where rubber compounds are free of sulphur: Type Slimline 'SL SF'.• Tests of fuel samples verified that the sulphur content of the fuel is not increased, even if the medium remains for a long time within the hose. • It fulfills all requirements of the relevant hose standards. Properties are equally good or even better than those of standard Slimline hoses.
Size	DN 21
Product Sheet	GR 11

34

0

Type Slimline 16 AdBlue

Slimline 16 AdBlue

Additional Info

Add to compare

Type Slimline 16 AdBlue

Hose for AdBlue^{^®} (DEF/AUS 32/ARLA 32) urea solution, black or blue.

Quality dispensing hoses SLIMLINE 16 AdBlue for urea solution.
Correspond to EN 1360.Dispensing hose DN 16 for the refilling of light and heavy vehicles with AdBlue^® (AUS 32, DEF, ARLA 32) urea solution to ISO 22241.
The highly flexible hose is well suitable for MPD hose retraction systems and allows small bending radii and a good handling.
In combination with the appropriate stainless steel hose couplings (pages 203/205), the plasticiser-free and leaching-resistant lining guarantees constant purity of the dispensed urea solution.

DN 16

Quality dispensing hoses SLIMLINE 16 AdBlue for urea solution.
Correspond to EN 1360.Dispensing hose DN 16 for the refilling of light and heavy vehicles with AdBlue^® (AUS 32, DEF, ARLA 32) urea solution to ISO 22241.
The highly flexible hose is well suitable for MPD hose retraction systems and allows small bending radii and a good handling.
In combination with the appropriate stainless steel hose couplings (pages 203/205), the plasticiser-free and leaching-resistant lining guarantees constant purity of the dispensed urea solution.

35

0

Universal Pump Hose

FLUORLINE universal pump hose for chemicals, petroleum based products, for propane, butane and other L.P. gases, as well as solvents as per resistance chart.

Ideal for highly sensitive media such as AdBlue^® urea solution (DEF, ARLA 32, AUS 32). Resistant against all common cleaning agents. Temperature range -40° to +100° C. Burst pressure >64 bar.

DN 16

FLUORLINE universal pump hose for chemicals, petroleum based products, for propane, butane and other L.P. gases, as well as solvents as per resistance chart.

Ideal for highly sensitive media such as AdBlue^® urea solution (DEF, ARLA 32, AUS 32). Resistant against all common cleaning agents. Temperature range -40° to +100° C. Burst pressure >64 bar.

Product Name	Type EFL 16
Short Description	Universal Pump Hose
Description	FLUORLINE universal pump hose for chemicals, petroleum based products, for propane, butane and other L.P. gases, as well as solvents as per resistance chart. Ideal for highly sensitive media such as AdBlue^® urea solution (DEF, ARLA 32, AUS 32). Resistant against all common cleaning agents. Temperature range -40° to +100° C. Burst pressure >64 bar.
Application	Ultra flexible universal hose with smooth lining of THV fluoropolymer. Smooth cover of electrically conductive rubber. No metallic parts in the reinforcements. Application: Suitable i.e. for barrel pumps, AdBlue^® urea dispensing, as zero emission petrol pump hose and as connection hose for mechanical engineering applications. Due to the small minimum bending radius also suitable for robot filling systems. Properties of the fluoropolymer lining: seamlessly extruded, smooth. Exceptional antistick properties, therefore low pressure drop and easy cleaning. Non-leaching and non-discolouring, therefore suitable for the transfer of highly pure products. Resistant to diffusion, 'smell-tight', therefore suitable for use in closed rooms. Conductivity: 'OHM' hose, fulfils requirements of EN 12115 and TRGS 727 (BGR 132). According CENELEC Standard CLC/TR 50404 hoses up to OD 30 mm, particularly petrol pump hoses up to OD 32 mm do not have to be conductive through the hose wall from inside to outside. Electrical conductivity <10⁶ Ω between hose ends, presumed a professional assembly with below mentioned fittings. The hose may be used in Ex-zones for the transfer of explosive media. Cold flexibility: FLUORLINE can be used in regions with very low temperatures, up to -40° C.
Comment	AdBlue^® is a registered trademark of VDA.
Lining	Fluoropolymer THV, seamless, transparent, smooth/mirror-like, non leaching, non discolouring, non hardening, resistant against diffusion
Reinforcements	Two textile braids
Cover	Chloroprene (CR), black, smooth, conductive, resistance against weathering and ozone, flame resistant
Marking	With continuous and permanent laser marking
Marking Sample	ELAFLEX FLUORLINE EFL 16 · b-w-r · EN 1360 TYPE 1 · EN 12115 · EN 1762 · Ω · 25 bar · · MADE IN GERMANY · · 1Q-20
Size	DN 16
Product Sheet	Page 113-114

36

0

Universal Pump Hose

FLUORLINE universal pump hose for chemicals, petroleum based products, for propane, butane and other L.P. gases, as well as solvents as per resistance chart.

Ideal for highly sensitive media such as AdBlue^® urea solution (DEF, ARLA 32, AUS 32). Resistant against all common cleaning agents. Temperature range -40° to +100° C. Burst pressure >64 bar.

DN 21

FLUORLINE universal pump hose for chemicals, petroleum based products, for propane, butane and other L.P. gases, as well as solvents as per resistance chart.

Ideal for highly sensitive media such as AdBlue^® urea solution (DEF, ARLA 32, AUS 32). Resistant against all common cleaning agents. Temperature range -40° to +100° C. Burst pressure >64 bar.

Product Name	Type EFL 21
Short Description	Universal Pump Hose
Description	FLUORLINE universal pump hose for chemicals, petroleum based products, for propane, butane and other L.P. gases, as well as solvents as per resistance chart. Ideal for highly sensitive media such as AdBlue^® urea solution (DEF, ARLA 32, AUS 32). Resistant against all common cleaning agents. Temperature range -40° to +100° C. Burst pressure >64 bar.
Application	Ultra flexible universal hose with smooth lining of THV fluoropolymer. Smooth cover of electrically conductive rubber. No metallic parts in the reinforcements. Application: Suitable i.e. for barrel pumps, AdBlue^® urea dispensing, as zero emission petrol pump hose and as connection hose for mechanical engineering applications. Due to the small minimum bending radius also suitable for robot filling systems. Properties of the fluoropolymer lining: seamlessly extruded, smooth. Exceptional antistick properties, therefore low pressure drop and easy cleaning. Non-leaching and non-discolouring, therefore suitable for the transfer of highly pure products. Resistant to diffusion, 'smell-tight', therefore suitable for use in closed rooms. Conductivity: 'OHM' hose, fulfils requirements of EN 12115 and TRGS 727 (BGR 132). According CENELEC Standard CLC/TR 50404 hoses up to OD 30 mm, particularly petrol pump hoses up to OD 32 mm do not have to be conductive through the hose wall from inside to outside. Electrical conductivity <10⁶ Ω between hose ends, presumed a professional assembly with below mentioned fittings. The hose may be used in Ex-zones for the transfer of explosive media. Cold flexibility: FLUORLINE can be used in regions with very low temperatures, up to -40° C.
Comment	AdBlue^® is a registered trademark of VDA.
Lining	Fluoropolymer THV, seamless, transparent, smooth/mirror-like, non leaching, non discolouring, non hardening, resistant against diffusion
Reinforcements	Two textile braids
Cover	Chloroprene (CR), black, smooth, conductive, resistance against weathering and ozone, flame resistant
Marking	Continuous marking with blue / white / red marking
Marking Sample	ELAFLEX FLUORLINE EFL 21 · EN 12115 · Ω · 16 bar · · MADE IN GERMANY · · 1Q-20
Size	DN 21
Product Sheet	Page 113-114

37

0

Liquid Petroleum Gas Hose

'Orange Band' Liquefied Petroleum Gas hose to EN 1762.
For propane, butane and their mixtures to EN 589. As the hose lining is resistant to diffusion the hose is also suitable for natural gas.
Use with propene (propylene) possible - pricking required. Not suitable for ammonia. Rugged and long-lasting construction with low tensile braids.
Burst pressure >100 bar. Temperature range -40° C up to +70° C (Special type LPG-LT does not crack down to -50° C).
Approved by DVGW, approval No. DG-4621 AU 0049.

DN 10 to DN 200

'Orange Band' Liquefied Petroleum Gas hose to EN 1762.
For propane, butane and their mixtures to EN 589. As the hose lining is resistant to diffusion the hose is also suitable for natural gas.
Use with propene (propylene) possible - pricking required. Not suitable for ammonia. Rugged and long-lasting construction with low tensile braids.
Burst pressure >100 bar. Temperature range -40° C up to +70° C (Special type LPG-LT does not crack down to -50° C).
Approved by DVGW, approval No. DG-4621 AU 0049.

38

0

Hose for L.P. Gas Dispensers
black or orange.

Hoses for L.P. Gas dispensers. Meet EN 1762 standard.
For propane, butane and their mixtures to EN 589. Highly flexible and long-lasting construction.
Burst pressure >100 bar. Temperature range -40° C up to +70° C.
DVGW and AS 1869 approved.

DN 16

Hoses for L.P. Gas dispensers. Meet EN 1762 standard.
For propane, butane and their mixtures to EN 589. Highly flexible and long-lasting construction.
Burst pressure >100 bar. Temperature range -40° C up to +70° C.
DVGW and AS 1869 approved.

39

0

Standard hose for L.P. Gas Dispensers
black or orange.

Hoses for L.P. Gas dispensers. Meet EN 1762 standard.
For propane, butane and their mixtures. Highly flexible and long-lasting construction.
Burst pressure >100 bar. Temperature range -30° C up to +70° C.
DVGW and AS 1869 approved.

DN 16

Hoses for L.P. Gas dispensers. Meet EN 1762 standard.
For propane, butane and their mixtures. Highly flexible and long-lasting construction.
Burst pressure >100 bar. Temperature range -30° C up to +70° C.
DVGW and AS 1869 approved.

40

0

Chemical Hose (without / with steel helix)

'Lilac Band' multi purpose hose for chemicals, acids (except for concentr. oxidising acids), alkalis, salt solutions, alcohols, polar solvents, acetates, aldehydes, ester, ketones, hot cooling water, hot air, not oily.
Temperature range -40° up to +100° C (depending on medium). Open steam cleaning up to +150° C / max. 30 min.Not suitable for aliphatic, aromatic and halogenated hydrocarbons, fuels, chlorine, ether, tar oils and oxidising acids.

DN 13 to DN 150

'Lilac Band' multi purpose hose for chemicals, acids (except for concentr. oxidising acids), alkalis, salt solutions, alcohols, polar solvents, acetates, aldehydes, ester, ketones, hot cooling water, hot air, not oily.
Temperature range -40° up to +100° C (depending on medium). Open steam cleaning up to +150° C / max. 30 min.Not suitable for aliphatic, aromatic and halogenated hydrocarbons, fuels, chlorine, ether, tar oils and oxidising acids.

41

0

Chemical Hose for pressure only (without helix)

'Lilac Band' multi purpose hose for chemicals, acids (except for concentr. oxidising acids), alkalis, salt solutions, alcohols, polar solvents, acetates, aldehydes, ester, ketones, hot cooling water, hot air, not oily.
Temperature range -40° up to +100° C (depending on medium). Open steam cleaning up to +150° C / max. 30 min.
Not suitable for aliphatic, aromatic and halogenated hydrocarbons, fuels, chlorine, ether, tar oils and oxidising acids.

DN 13 to DN 50

'Lilac Band' multi purpose hose for chemicals, acids (except for concentr. oxidising acids), alkalis, salt solutions, alcohols, polar solvents, acetates, aldehydes, ester, ketones, hot cooling water, hot air, not oily.
Temperature range -40° up to +100° C (depending on medium). Open steam cleaning up to +150° C / max. 30 min.
Not suitable for aliphatic, aromatic and halogenated hydrocarbons, fuels, chlorine, ether, tar oils and oxidising acids.

42

0

Chemical Host for suction + discharge (with steel helix)

'Lilac Band' multi purpose hose for chemicals, acids (except for concentr. oxidising acids), alkalis, salt solutions, alcohols, polar solvents, acetates, aldehydes, ester, ketones, hot cooling water, hot air, not oily.
Temperature range -40° up to +100° C (depending on medium). Open steam cleaning up to +150° C / max. 30 min.
Not suitable for aliphatic, aromatic and halogenated hydrocarbons, fuels, chlorine, ether, tar oils and oxidising acids.

DN 25 to DN 150

'Lilac Band' multi purpose hose for chemicals, acids (except for concentr. oxidising acids), alkalis, salt solutions, alcohols, polar solvents, acetates, aldehydes, ester, ketones, hot cooling water, hot air, not oily.
Temperature range -40° up to +100° C (depending on medium). Open steam cleaning up to +150° C / max. 30 min.
Not suitable for aliphatic, aromatic and halogenated hydrocarbons, fuels, chlorine, ether, tar oils and oxidising acids.

43

0

Solvent Hose (without / with steel helix)

Solvent hose 'Blue Band' for most solvents, paints (also water based), water lacquer, petroleum products, alcohols, aldehydes, esters and ketones.
In short term operation also suitable for aromatic and chlorinated hydrocarbons. Further details see resistance chart.
Temperature range -20° up to +80° C, short term up to +100° C. Open steam cleaning up to +130° C / max. 30 min.

DN 13 to DN 150

Solvent hose 'Blue Band' for most solvents, paints (also water based), water lacquer, petroleum products, alcohols, aldehydes, esters and ketones.
In short term operation also suitable for aromatic and chlorinated hydrocarbons. Further details see resistance chart.
Temperature range -20° up to +80° C, short term up to +100° C. Open steam cleaning up to +130° C / max. 30 min.

44

0

Solvent Hose for pressure only (without helix)

Solvent hose 'Blue Band' for most solvents, paints (also water based), water lacquer, petroleum products, alcohols, aldehydes, esters and ketones. In short term operation also suitable for aromatic and chlorinated hydrocarbons.
Further details see resistance chart.
Temperature range -20° up to +80° C, short term up to +100° C. Open steam cleaning up to +130° C / max. 30 min.

DN 9 to DN 25

Solvent hose 'Blue Band' for most solvents, paints (also water based), water lacquer, petroleum products, alcohols, aldehydes, esters and ketones. In short term operation also suitable for aromatic and chlorinated hydrocarbons.
Further details see resistance chart.
Temperature range -20° up to +80° C, short term up to +100° C. Open steam cleaning up to +130° C / max. 30 min.

45

0

Solvent Hose for suction + discharge (with steel helix)

Solvent hose 'Blue Band' for most solvents, paints (also water based), water lacquer, petroleum products, alcohols, aldehydes, esters and ketones. In short term operation also suitable for aromatic and chlorinated hydrocarbons.
Further details see resistance chart.
Temperature range -20° up to +80° C, short term up to +100° C. Open steam cleaning up to +130° C / max. 30 min.

DN 25 to DN 150

Solvent hose 'Blue Band' for most solvents, paints (also water based), water lacquer, petroleum products, alcohols, aldehydes, esters and ketones. In short term operation also suitable for aromatic and chlorinated hydrocarbons.
Further details see resistance chart.
Temperature range -20° up to +80° C, short term up to +100° C. Open steam cleaning up to +130° C / max. 30 min.

46

0

Universal Tank Hose (without / with helix)

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

DN 13 to DN 150

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

47

0

Universal Tank Hose (without helix)

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

DN 13 to DN 38

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

48

0

Universal Tank Hose (with steel helix)

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

DN 19 to DN 150

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

49

0

Universal Tank Hose 'Light' (with steel helix)

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

DN 38 to DN 100

Blue-white-blue universal tank hoses for almost all liquid and pasty chemical and petroleum based products and solvents.
Temperature range -30° up to +100° C depending on medium. Steaming out for cleaning and sterilisation permissable up to +130° C up to max. 30 minutes (open ends).
Meets EN 12115.

50

0

'POLYPAL CLEAN' (without / with helix)

Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

DN 13 to DN 100

Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

Product Name	Type PCD / PCS
Short Description	'POLYPAL CLEAN' (without / with helix)
Description	Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart. Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends). Meets EN 12115.
Application	PCD: As pressure hose for discharge in wet and dry hose systems. Also suitable as reel hose provided the inner pressure reaches min. 0,5 bar to avoid kinking. PCS: Suction and discharge hose for barrels, containers, tanks and fixed installations. The steel helix ensures that the hose maintains its shape during suction and gravity operations.
Comment	CHEMICAL RESISTANCE POLYPAL CLEAN is universally suitable for most liquids, high viscous and powdery media, except of brome, brominated hydrocarbons, chlorine, chlorosulfonic acid, fluorine and strongly oxidising acids such as concentrated nitric acid, smoking sulfuric acid (oleum). For details see chemical resistance chart. DISCOLOURING The hose proved that critical mediums such as toluene and acetone show no perceptible discolouring of the conveyed product, even in wet hose conditions. CLEANING AND TEMPERATURE RESISTANCE Cover: Clean surfaces due to scuff-proof light grey rubber. Lining: The smooth UPE lining allows good drainage and easy cleaning when changing medium. UPE is resistant against all commercial cleaning agents up to +100° Celsius. The 'open' steaming out and sterilisation is possible with saturated steam up to +130° Celsius for max. 30 minutes. Do not use steam nozzles which can destroy the lining by localised overheating.
Lining	UPE bright, with OHM conductive stripe, smooth, no discolouration, abrasion resistant, electrically conductive. FDA conform *)
Reinforcements	Textile braids, form SD additionally with galvanised steel helix
Cover	EPDM light grey with OHM conductive stripe, electrically conductive. FDA conform *)
Certificates	UPE lining and all layers of rubber conform to FDA and regulations (EC) No. 1935/2004; Material of lining to (EU) No. 10/2011. All layers of rubber correspond to Recommendation XXI of BfR. Confirmation of mentioned electrostatic properties by ZAFT, certificate No. ZAFT Ex 209906-9.
*	*) Lining and cover corresponds to FDA guideline 21 CFR 177.1550 and CFR 178.3297 and fulfills the requirements of EU regulations No. 1935/2004 and No. 10/2011.
Marking	Blue-white-blue coloured spiral and abrasion resistant continuous embossing
Marking Sample	ELAFLEX PCD 25 · POLYPAL CLEAN · EN 12115 · UPE · D · Ω/T · 100ºC · 16 BAR · · MADE IN GERMANY · · 1Q-20
Size	DN 13 to DN 100
Product Sheet	Page 121c-121d
	Page PAL 03-04

51

0

Universal-Pharmacy-Hose 'Clean' (without helix)

Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

DN 13 to DN 38

Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

Product Name	Type PCD
Short Description	Universal-Pharmacy-Hose 'Clean' (without helix)
Description	Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart. Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends). Meets EN 12115.
Application	As pressure hose for discharge in wet and dry hose systems. Also suitable as reel hose provided the inner pressure reaches min. 0,5 bar to avoid kinking.
Comment	CHEMICAL RESISTANCE POLYPAL CLEAN is universally suitable for most liquids, high viscous and powdery media, except of brome, brominated hydrocarbons, chlorine, chlorosulfonic acid, fluorine and strongly oxidising acids such as concentrated nitric acid, smoking sulfuric acid (oleum). For details see chemical resistance chart. DISCOLOURING The hose proved that critical mediums such as toluene and acetone show no perceptible discolouring of the conveyed product, even in wet hose conditions. CLEANING AND TEMPERATURE RESISTANCE Cover: Clean surfaces due to scuff-proof light grey rubber. Lining: The smooth UPE lining allows good drainage and easy cleaning when changing medium. UPE is resistant against all commercial cleaning agents up to +100° Celsius. The 'open' steaming out and sterilisation is possible with saturated steam up to +130° Celsius for max. 30 minutes. Do not use steam nozzles which can destroy the lining by localised overheating.
Lining	UPE bright, with OHM conductive stripe, smooth, no discolouration, abrasion resistant, electrically conductive. FDA conform *)
Reinforcements	Textile braids, form SD additionally with galvanised steel helix
Cover	EPDM light grey with OHM conductive stripe, electrically conductive. FDA conform *)
Certificates	UPE lining and all layers of rubber conform to FDA and regulations (EC) No. 1935/2004; Material of lining to (EU) No. 10/2011. All layers of rubber correspond to Recommendation XXI of BfR. Confirmation of mentioned electrostatic properties by ZAFT, certificate No. ZAFT Ex 209906-9. Manufacturer declaration - absence of silicone.
*	*) Lining and cover corresponds to FDA guideline 21 CFR 177.1550 and CFR 178.3297 and fulfills the requirements of EU regulations No. 1935/2004 and No. 10/2011.
Marking	Blue-white-blue coloured spiral and abrasion resistant continuous embossing
Marking Sample	ELAFLEX PCD 25 · POLYPAL CLEAN · EN 12115 · UPE · D · Ω/T · 100ºC · 16 BAR · · MADE IN GERMANY · · 1Q-20
Size	DN 13 to DN 38
Product Sheet	Page 121c-121d
	Page PAL 03-04

52

0

Universal-Pharmacy-Hose 'Clean' (with steel helix)

Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

DN 25 to DN 100

Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

Product Name	Type PCS
Short Description	Universal-Pharmacy-Hose 'Clean' (with steel helix)
Description	Universal hose POLYPAL CLEAN with light grey cover, for clean chemicals, cosmetics, paints and glues, washing and cleaning products, hygienic / sanitary products and foodstuffs, see resistance chart. Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends). Meets EN 12115.
Application	Suction and discharge hose for barrels, containers, tanks and fixed installations. The steel helix ensures that the hose maintains its shape during suction and gravity operations.
Comment	CHEMICAL RESISTANCE POLYPAL CLEAN is universally suitable for most liquids, high viscous and powdery media, except of brome, brominated hydrocarbons, chlorine, chlorosulfonic acid, fluorine and strongly oxidising acids such as concentrated nitric acid, smoking sulfuric acid (oleum). For details see chemical resistance chart. DISCOLOURING The hose proved that critical mediums such as toluene and acetone show no perceptible discolouring of the conveyed product, even in wet hose conditions. CLEANING AND TEMPERATURE RESISTANCE Cover: Clean surfaces due to scuff-proof light grey rubber. Lining: The smooth UPE lining allows good drainage and easy cleaning when changing medium. UPE is resistant against all commercial cleaning agents up to +100° Celsius. The 'open' steaming out and sterilisation is possible with saturated steam up to +130° Celsius for max. 30 minutes. Do not use steam nozzles which can destroy the lining by localised overheating.
Lining	UPE bright, with OHM conductive stripe, smooth, no discolouration, abrasion resistant, electrically conductive. FDA conform *)
Reinforcements	Textile braids, form SD additionally with galvanised steel helix
Cover	EPDM light grey with OHM conductive stripe, electrically conductive. FDA conform *)
Certificates	UPE lining and all layers of rubber conform to FDA and regulations (EC) No. 1935/2004; Material of lining to (EU) No. 10/2011. All layers of rubber correspond to Recommendation XXI of BfR. Confirmation of mentioned electrostatic properties by ZAFT, certificate No. ZAFT Ex 209906-9. Manufacturer declaration - absence of silicone.
*	*) Lining and cover corresponds to FDA guideline 21 CFR 177.1550 and CFR 178.3297 and fulfills the requirements of EU regulations No. 1935/2004 and No. 10/2011.
Marking	Blue-white-blue coloured spiral and abrasion resistant continuous embossing
Marking Sample	ELAFLEX PCS 50 POLYPAL CLEAN · EN 12115 · UPE · SD · Ω/T · 100ºC · 16 BAR · · MADE IN GERMANY · · 1Q-20
Size	DN 25 to DN 100
Product Sheet	Page 121c-121d
	Page PAL 03-04

53

0

Foodstuff-Hose (without / with helix)

White band hose for all foodstuff s, milk, oils, fats, flour, molasses, dextrose and sirups.
Temperature range -25° to +90° Celsius. The hoses can be temporarily steamed out with up to +130° C.

DN 19 to DN 100

White band hose for all foodstuff s, milk, oils, fats, flour, molasses, dextrose and sirups.
Temperature range -25° to +90° Celsius. The hoses can be temporarily steamed out with up to +130° C.

54

0

Foodstuff-Hose (without helix)

White band hose for all foodstuff s, milk, oils, fats, flour, molasses, dextrose and sirups.
Temperature range -25° to +90° Celsius. The hoses can be temporarily steamed out with up to +130° C.

DN 19 to DN 38

White band hose for all foodstuff s, milk, oils, fats, flour, molasses, dextrose and sirups.
Temperature range -25° to +90° Celsius. The hoses can be temporarily steamed out with up to +130° C.

55

0

Foodstuff-Hose (with steel helix)

White band hose for all foodstuff s, milk, oils, fats, flour, molasses, dextrose and sirups.
Temperature range -25° to +90° Celsius. The hoses can be temporarily steamed out with up to +130° C.

DN 50 to DN 100

White band hose for all foodstuff s, milk, oils, fats, flour, molasses, dextrose and sirups.
Temperature range -25° to +90° Celsius. The hoses can be temporarily steamed out with up to +130° C.

56

0

Ammoniac-Hose

Ammoniac hose according to EN ISO 5771 for water-free, liquid and gas ammonia.
Temperature range -40° C up to +55° C. Burst pressure >125 bar.

DN 13 to DN 50

Ammoniac hose according to EN ISO 5771 for water-free, liquid and gas ammonia.
Temperature range -40° C up to +55° C. Burst pressure >125 bar.

57

0

Hot-Air-Compressor-Hose

Hot Air Compressor Hose for discharge of silo bulk vehicles.
Temperature range -30° C up to +160° C.
Special type available with steel helix.

DN 50 to DN 110

Hot Air Compressor Hose for discharge of silo bulk vehicles.
Temperature range -30° C up to +160° C.
Special type available with steel helix.

58

0

ELAFLON PTFE (without / with helix)

Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar.
Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min.
Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.

DN 13 to DN 100

Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar.
Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min.
Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.

Product Name	Type PTFE D / PTFE
Short Description	ELAFLON PTFE (without / with helix)
Description	Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart. Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar. Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min. Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.
Application	Application PTFE D (without helix): As pressure hose for discharge and barrel pumps in wet and dry hose systems. Also suitable as reel hose. Application PTFE (with helix): As suction and discharge hose for barrels, containers, rail tank cars, tankers and fixed installations. The steel helix ensures that the hose keeps in shape during suction and gravity operations, even with tight bending radii.
Comment	The PTFE lining is electrically conductive, seamlessly extruded, and smooth – therefore low pressure drop in service and easy cleaning properties. No cross contamination or discoloration of media thus being excellent when very pure media are being carried. Lining conform to FDA / USP Class VI.Electrical conductivity: Ω/T-type to EN 12115. Electrical resistance of <10⁶ OHM between hose ends, <10⁹ OHM from lining to cover, through the hose wall. Suitable for use in EX-Zones 0, 1 and 2. Easy assembling: Ω/T-hoses have the added advantage that metallic conductive elements do not have to be connected to the hose fittings.
Lining	PTFE, electrically conductive, black, seamless, smooth bore
Reinforcements	High-tensile, temperature resistant, textile braids, Form SD additionally with galvanised steel helix
Intermed. Layer	Adhesive rubber compound, conductive
Cover	EPDM, electrically conductive, black, abrasion and flame resistant, resistant against weather and ageing
Marking	Blue-white-red coloured spiral and abrasion resistant continuous embossing
Marking Sample	ELAFLEX PTFE 25 · EN 12115 · D · Ω /T · ELAFLON PTFE · FDA · 150° C · 16 BAR · · MADE IN GERMANY · · 4Q-18
Size	DN 13 to DN 100
Product Sheet	Page 127-128
	Page PAL 07-08

59

0

ELAFLON PTFE (without helix)

Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar.
Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min.
Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.

DN 13 to DN 25

Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar.
Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min.
Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.

60

0

ELAFLON PTFE (with helix)

Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar.
Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min.
Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.

DN 19 to DN 100

Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar.
Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min.
Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.

Product Name	Type PTFE
Short Description	ELAFLON PTFE (with helix)
Description	Universal hose ELAFLON PTFE with electrically conductive, seamless lining of PTFE (Polytetrafluorethylene). Suitable for all commonly used chemicals, see resistance chart. Suitable for both suction and delivery (Type PTFE D = delivery). Working pressure up to 16 bar, burst pressure >64 bar. Temperature range from -30° up to +150° Celsius (depending on medium). Chemical resistance see resistance chart. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min. Meets EN 12115. FDA und USP Class VI conform according EC regulations 1935/2004 and 10/2011.
Application	As suction and discharge hose for barrels, containers, rail tank cars, tankers and fixed installations. The steel helix ensures that the hose keeps in shape during suction and gravity operations, even with tight bending radii.
Comment	The PTFE lining is electrically conductive, seamlessly extruded, and smooth – therefore low pressure drop in service and easy cleaning properties. No cross contamination or discoloration of media thus being excellent when very pure media are being carried. Lining conform to FDA / USP Class VI.Electrical conductivity: Ω/T-type to EN 12115. Electrical resistance of <10⁶ OHM between hose ends, <10⁹ OHM from lining to cover, through the hose wall. Suitable for use in EX-Zones 0, 1 and 2. Easy assembling: Ω/T-hoses have the added advantage that metallic conductive elements do not have to be connected to the hose fittings.
Lining	PTFE, electrically conductive, black, seamless, smooth bore
Reinforcements	High-tensile, temperature resistant, textile braids, additionally with galvanised steel helix
Cover	EPDM, electrically conductive, black, abrasion and flame resistant, resistant against weather and ageing
Marking	Blue-white-red coloured spiral and abrasion resistant continuous embossing
Marking Sample	ELAFLEX PTFE 25 · EN 12115 · D · Ω /T · ELAFLON PTFE · FDA · 150° C · 16 BAR · · MADE IN GERMANY · · 4Q-18
Size	DN 19 to DN 100
Product Sheet	Page 127-128
	Page PAL 07-08

61

0

ELAFLON PLUS FEP (without / with helix)

Universal hose ELAFLON PLUS FEP with seamless FEP lining, resistant to all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type FEP D = delivery only). W.P. up to 16 bar, burst pressure >64 bar.
Temperature range from -30° C up to +100° C, briefly up to +130° C. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min (open system).
Meets EN 12115.

DN 13 to DN 100

Universal hose ELAFLON PLUS FEP with seamless FEP lining, resistant to all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type FEP D = delivery only). W.P. up to 16 bar, burst pressure >64 bar.
Temperature range from -30° C up to +100° C, briefly up to +130° C. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min (open system).
Meets EN 12115.

Product Name	Type FEP D / FEP
Short Description	ELAFLON PLUS FEP (without / with helix)
Description	Universal hose ELAFLON PLUS FEP with seamless FEP lining, resistant to all commonly used chemicals, see resistance chart. Suitable for both suction and delivery (Type FEP D = delivery only). W.P. up to 16 bar, burst pressure >64 bar. Temperature range from -30° C up to +100° C, briefly up to +130° C. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min (open system). Meets EN 12115.
Application	Application FEP D (without Helix): As pressure hose for discharge and barrel pumps in wet and dry hose systems. Also suitable as reel hose. Application FEP (with helix): As suction and discharge hose for containers, rail tankers, tankers and fixed installations. The steel helix ensures that the hose keeps in shape during suction and gravity operations, even with tight bending radii.
Comment	Technical properties of the FEP lining: Seamlessly extruded, smooth, therefore low pressure drop in service, easy cleaning properties. Excellent draining capability, no cross contamination or discoloration of media thus being excellent when very pure media is being carried. Conform to FDA and USP Class VI. Electrical conductivity: 'Ω-C'-Type to EN 12115, only the hose cover is electrically conductive. To achieve this, externally grey versions (DN 50 and below) have a OHM conductive stripe for a safe electrical conductivity of the hose assembly. Nonetheless, the hose type FEP is not recommend for use with flammable media in EX-Zones.
Lining	FEP, seamless, transparent, smooth bore, electrically non-conductive
Reinforcements	Textile braids, form SD additionally with galvanised steel helix
Intermed. Layer	Adhesive rubber compound, grey / EPDM, conductive
Cover	EPDM, electrically conductive, light grey with OHM conductive stripe (up to DN 50) or black (DN 63 – 100). Abrasion and flame resistant, resistant against weather and ageing.
Marking	Blue-white-red coloured spiral and abrasion resistant continuous embossing
Marking Sample	ELAFLEX FEP 25 · ELAFLON PLUS · EN 12115 · FEP · D · 100 ˚ C · Ω · 16 BAR · · ContiTech · MADE IN GERMANY · 1Q-17
Size	DN 13 to DN 100
Product Sheet	Page 125-126
	Page PAL 05-06

62

0

Universal-Hose (without helix)

Universal hose ELAFLON PLUS FEP with seamless FEP lining, resistant to all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type FEP D = delivery only). W.P. up to 16 bar, burst pressure >64 bar.
Temperature range from -30° C up to +100° C, briefly up to +130° C. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min (open system).
Meets EN 12115.

DN 13 to DN 25

Universal hose ELAFLON PLUS FEP with seamless FEP lining, resistant to all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type FEP D = delivery only). W.P. up to 16 bar, burst pressure >64 bar.
Temperature range from -30° C up to +100° C, briefly up to +130° C. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min (open system).
Meets EN 12115.

63

0

Universal-Hose (with helix)

Universal hose ELAFLON PLUS FEP with seamless FEP lining, resistant to all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type FEP D = delivery only). W.P. up to 16 bar, burst pressure >64 bar.
Temperature range from -30° C up to +100° C, briefly up to +130° C. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min (open system).
Meets EN 12115.

DN 19 to DN 100

Universal hose ELAFLON PLUS FEP with seamless FEP lining, resistant to all commonly used chemicals, see resistance chart.
Suitable for both suction and delivery (Type FEP D = delivery only). W.P. up to 16 bar, burst pressure >64 bar.
Temperature range from -30° C up to +100° C, briefly up to +130° C. Steaming out for cleaning and sterilisation permissible up to +150° C, max. 30 min (open system).
Meets EN 12115.

64

0

Universal-Helical-Hose

Fluorflex 2 is a new generation high performance chemical hose to DIN 26054, combining the universal chemical resistance of PTFE with exceptional flexibility
and tight bending radius.

It is the only known hose with a corrugated PTFE-lining which is available in coils, and suitable for on-site fitting assembly. Long lead times or the necessity to stock complete hose assemblies not longer apply.

The requirements 'Ω/T conductivity' (may be used in EX-zones), FDA conformity and high temperature resistance are also satisfied by Fluorflex.

DN 20 to DN 50

Fluorflex 2 is a new generation high performance chemical hose to DIN 26054, combining the universal chemical resistance of PTFE with exceptional flexibility
and tight bending radius.

It is the only known hose with a corrugated PTFE-lining which is available in coils, and suitable for on-site fitting assembly. Long lead times or the necessity to stock complete hose assemblies not longer apply.

The requirements 'Ω/T conductivity' (may be used in EX-zones), FDA conformity and high temperature resistance are also satisfied by Fluorflex.

Product Name	Type FXD
Short Description	Universal-Helical-Hose
Description	Fluorflex 2 is a new generation high performance chemical hose to DIN 26054, combining the universal chemical resistance of PTFE with exceptional flexibility and tight bending radius. It is the only known hose with a corrugated PTFE-lining which is available in coils, and suitable for on-site fitting assembly. Long lead times or the necessity to stock complete hose assemblies not longer apply. The requirements 'Ω/T conductivity' (may be used in EX-zones), FDA conformity and high temperature resistance are also satisfied by Fluorflex.
Comment	An extremely flexible universal hose with helically wound PTFE liner, suitable for all common media in use). Applications in the petrochemical, pharmaceutical and food industry. Temperature range -20° C up to +150° C, permanent use. Briefly, also higher temperatures possible depending on medium. Cleaning: Flush with all common media and procedures. Steaming out (open system) admissable up to +180° C, max. 30 minutes. Nominal pressure PN 16 bar, burst pressure >64 bar. Electrical resistance <10⁶ Ohm between hose ends, through the hose <10⁹ Ohm (from inside to outside, 'Ω / T'). No connection of wires to metal parts necessary. Compared to PTFE hoses with braided metal cover, no possibility of injuries from damaged wires, and considerably lower heat transmission. ) See resistance chart ELAFLEX hoses
Lining	PTFE, transparent, with patented OHM-conductive spirals, seamlessly extruded, spirally wound, non leaching, non discolouring, very good anti-stick properties
Reinforcements	High temp. resistant aramide braid
Intermed. Layer	EPDM, black, electrically conductive, mechanical binding to the liner
Cover	EPDM, black, electrically conductive, abrasion and flame resistant, UV and ozone resistant
Marking	Spiral band Yellow/Blue/White and continuous embossing
Marking Sample	ELAFLEX FXD 25 . FLUORFLEX 2 · DIN 26054 · PTFE · Ω/T · FDA · 150° C · 16 BAR · · ContiTech · MADE IN GERMANY · 01.17
Size	DN 20 to DN 50
Product Sheet	Information 2.08 E

65

0

Type EPH /
Type EPH-OHM /
Type EPH-OHM G

EPH

Additional Info

Add to compare

Type EPH /
Type EPH-OHM /
Type EPH-OHM G

ELAPHARM electrically isolating 'I', blue cover.
Corresponds to DIN 26055-3 / EN 16820, Type A. FDA conform.
Homogeneous elastomer hose construction with smooth, white Teflon^® PTFE liner.

DN 13 to DN 50

66

0

Electrically isolating 'I'.
Blue EPDM Cover, Lining PTFE white.

ELAPHARM electrically isolating 'I', blue cover.
Corresponds to DIN 26055-3 / EN 16820, Type A. FDA conform.
Homogeneous elastomer hose construction with smooth, white Teflon^® PTFE liner.

DN 13 to DN 50

67

0

Electrically conductive Ω/T.
Grey EPDM Cover, Lining PTFE black.

ELAPHARM OHM G electrically conductive 'Ω / T', light grey cover.
Corresponds to DIN 26055-3 / EN 16820, Type A. FDA conform.
Homogeneous elastomer hose construction with smooth, black Teflon^® PTFE liner.

DN 13 to DN 50

ELAPHARM OHM G electrically conductive 'Ω / T', light grey cover.
Corresponds to DIN 26055-3 / EN 16820, Type A. FDA conform.
Homogeneous elastomer hose construction with smooth, black Teflon^® PTFE liner.

68

0

Electrically conductive Ω/T.
Black EPDM Cover, Lining PTFE black.
only on request

ELAPHARM OHM G electrically conductive 'Ω / T', black cover.
Corresponds to DIN 26055-3 / EN 16820, Type A. FDA conform.
Homogeneous elastomer hose construction with smooth, black Teflon^® PTFE liner.

DN 13 to DN 50

ELAPHARM OHM G electrically conductive 'Ω / T', black cover.
Corresponds to DIN 26055-3 / EN 16820, Type A. FDA conform.
Homogeneous elastomer hose construction with smooth, black Teflon^® PTFE liner.

69

0

ElaSil^® silicone hose for cosmetics, pharmaceuticals and foodstuffs (with helix)

Silicone hose assemblies for high media purity requirements.

DN 13 to DN 76

Silicone hose assemblies for high media purity requirements.

70

0

Marine Collapsable Hose (without helix)

Type FHD is a collapsible marine bunkering hose. lt can be reeled up flat, takes little space to stow away and is easy to handle.
Used as pressure discharge hose for all petroleum based products with an aromatic content up to 50%, on bunkering ships, tankers as well as 'flexible pipeline'. Suitable for naval mobile supply and for offshore facilities.
Meets German military standard VG 95955 and EN 1765, type L.

DN 75 to DN 254

Type FHD is a collapsible marine bunkering hose. lt can be reeled up flat, takes little space to stow away and is easy to handle.
Used as pressure discharge hose for all petroleum based products with an aromatic content up to 50%, on bunkering ships, tankers as well as 'flexible pipeline'. Suitable for naval mobile supply and for offshore facilities.
Meets German military standard VG 95955 and EN 1765, type L.

71

0

Marine Hose (with helix)

Type STW is a marine suction and discharge hose for tanker vessels, also suitable for gravity discharge because the helix helps to keep the diameter round. As light bunker hose for all petroleum based products with an aromatic content up to 50 %, on bunkering ships, tankers and other ships. Ideal also as flexible duct for floating bridges to compensate for level differences.
Meets German military standard VG 95 955 and EN 1765, type S.

DN 50 to DN 200

Type STW is a marine suction and discharge hose for tanker vessels, also suitable for gravity discharge because the helix helps to keep the diameter round. As light bunker hose for all petroleum based products with an aromatic content up to 50 %, on bunkering ships, tankers and other ships. Ideal also as flexible duct for floating bridges to compensate for level differences.
Meets German military standard VG 95 955 and EN 1765, type S.

72

0

Bunkering-Hose (without / with helix)

Marine Cargo Hoses (Bunkering Hoses) with conical transition to the fitting and covered reinforcements. Vulcanised built-in flange nipples.
Meets EN 1765.

DN 100 to DN 300

Marine Cargo Hoses (Bunkering Hoses) with conical transition to the fitting and covered reinforcements. Vulcanised built-in flange nipples.
Meets EN 1765.

73

0

Bunkering-Hose (without helix)

Type SBL is a light weight and very flexible collapsible hose without helix for pressure service.
Meets category L 10 of EN 1765.
Suitable for manual handling, very flexible. The reinforcement is constructed in such a way that the hose keeps its whole diameter even with 1 bar flow pressure.
Type SBL is not suitable for gravity discharge and for suction.
Please avoid permanent kinking.

DN 100 to DN 250

Type SBL is a light weight and very flexible collapsible hose without helix for pressure service.
Meets category L 10 of EN 1765.
Suitable for manual handling, very flexible. The reinforcement is constructed in such a way that the hose keeps its whole diameter even with 1 bar flow pressure.
Type SBL is not suitable for gravity discharge and for suction.
Please avoid permanent kinking.

74

0

Bunkering-Hose (with helix)

Type SBS is the heavy standard bunkering hose with steel helix for suction and discharge.
Meets EN 1765 category S 15.
Recommended for crane operated dockside loading and unloading in harbours and refineries. Very robust and kink resistant. Electrically conductive due to metallic connection of steel helix with the hose tail.
On request, available in a non-electrically conductive version.

DN 150 to DN 300

Type SBS is the heavy standard bunkering hose with steel helix for suction and discharge.
Meets EN 1765 category S 15.
Recommended for crane operated dockside loading and unloading in harbours and refineries. Very robust and kink resistant. Electrically conductive due to metallic connection of steel helix with the hose tail.
On request, available in a non-electrically conductive version.

75

0

Hose for Hot Asphalt (with steel helix)

Hot Bitumen hose 'Brown Band', for filling of hot bitumen and heavy fuel oil.
Temperature range -25° C to max. +200° C.
Not suitable for lignite-tar oil and coal-tar oils.
Meets EN 13482.

DN 50 to DN 100

Hot Bitumen hose 'Brown Band', for filling of hot bitumen and heavy fuel oil.
Temperature range -25° C to max. +200° C.
Not suitable for lignite-tar oil and coal-tar oils.
Meets EN 13482.

76

0

Tar spraying and bitumen hose for road construction machines. (without / with steel helix)

Pressure hose for road construction machines, especially for hot bitumen and heavy heating oil.
Temperature range: - 25° C up to + 220° C.
Meets EN 13482, Type 2 SB/B (DN 19 and DN 32 analogue).

PLEASE NOTE: Not suitable for brown coal tar oil and coal oil (toluene).
Read the safety hints for the use of hot bitumen hoses on catalogue page 136.
Permanent operation temperatures above 220° C significantly reduces hose lifetime.

DN 19 to DN 50

Pressure hose for road construction machines, especially for hot bitumen and heavy heating oil.
Temperature range: - 25° C up to + 220° C.
Meets EN 13482, Type 2 SB/B (DN 19 and DN 32 analogue).

PLEASE NOTE: Not suitable for brown coal tar oil and coal oil (toluene).
Read the safety hints for the use of hot bitumen hoses on catalogue page 136.
Permanent operation temperatures above 220° C significantly reduces hose lifetime.

77

0

Hose for Hot Water

Hot Water hose for cold and hot water, seawater, cooling and swimming pool water.
Temperature range -45° C to +100° C. Short term up to +130° C.

DN 19 to DN 50

Hot Water hose for cold and hot water, seawater, cooling and swimming pool water.
Temperature range -45° C to +100° C. Short term up to +130° C.

78

0

Type SD PYROPAL (230)

SD PYROPAL (230)

Additional Info

Add to compare

Type SD PYROPAL (230)

Hose for Steam

Steam hose with steel braids for wet saturated steam up to 18 bar (+210° C) and hot water up to +120° C. For cold water up to 25 bar. Minimum burst pressure 180 bar (1:10 safety factor).
Not oil resistant.
Meets EN ISO 6134 Type 2A.

DN 13 to DN 50

Steam hose with steel braids for wet saturated steam up to 18 bar (+210° C) and hot water up to +120° C. For cold water up to 25 bar. Minimum burst pressure 180 bar (1:10 safety factor).
Not oil resistant.
Meets EN ISO 6134 Type 2A.

79

0

Composite hose FWS

Multi-layer thermoplastic hoses according to EN 13765. Delivery as checked hose assembly.
Lining: PP / PTFE / PA (6 types)

80

0

Composite hose FWS
Lining Polypropylen

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

DN 25 to DN 250

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

81

0

Composite hose FWS
Lining Polypropylen

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

DN 65 to DN 100

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

82

0

Composite hose FWS
Lining Polypropylen

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

DN 25 to DN 250

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

83

0

Composite hose FWS
Lining PTFE

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

DN 25 to DN 250

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range -30° C up to +100° C (depending on medium).

84

0

Composite hose FWS
Lining Polyamide

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range - 30° C up to + 100° C (depending on medium).

DN 50 to DN 100

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 14 bar, temperature range - 30° C up to + 100° C (depending on medium).

85

0

Composite hose FWS
Lining Polypropylene

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 7 bar, temperature range -30° C up to +80° C (depending on medium).

DN 75 to DN 250

Multi-layer thermoplastic hoses (composite hoses) to EN 13765, for suction and pressure operation. Delivery as hose assembly.
PN 7 bar, temperature range -30° C up to +80° C (depending on medium).

86

0

Universal Chemical Hose (with steel helix)

Universal chemical hose POLYPAL PLUS with seamless, black, conductive UPE lining.
For almost all liquid and pasty chemical and petroleum based products and solvents, see resistance chart PAL hoses.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

DN 13 to DN 100

Universal chemical hose POLYPAL PLUS with seamless, black, conductive UPE lining.
For almost all liquid and pasty chemical and petroleum based products and solvents, see resistance chart PAL hoses.
Temperature range -30° C up to +100° C, depending on medium. Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

87

0

Chemical Hose (without / with helix)

Chemical hose CHEMOPAL for alkalis, acids, acetates, aldehydes, amines, esters, ethers and ketones.
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +90° C). Steaming out for cleaning and sterilisation permissible up to +150° C / max. 30 min (open ends).
Meets EN 12115.

DN 13 to DN 150

Chemical hose CHEMOPAL for alkalis, acids, acetates, aldehydes, amines, esters, ethers and ketones.
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +90° C). Steaming out for cleaning and sterilisation permissible up to +150° C / max. 30 min (open ends).
Meets EN 12115.

88

0

Type CHEMOPAL oW (Form D)

CHEMOPAL oW (Form D)

Additional Info

Add to compare

Type CHEMOPAL oW (Form D)

Chemical Hose (without steel helix)

Chemical hose CHEMOPAL for alkalis, acids, acetates, aldehydes, amines, esters, ethers and ketones.
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +90° C). Steaming out for cleaning and sterilisation permissible up to +150° C / max. 30 min (open ends).
Meets EN 12115.

DN 13 to DN 50

Chemical hose CHEMOPAL for alkalis, acids, acetates, aldehydes, amines, esters, ethers and ketones.
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +90° C). Steaming out for cleaning and sterilisation permissible up to +150° C / max. 30 min (open ends).
Meets EN 12115.

89

0

Type CHEMOPAL mW (Form SD)

CHEMOPAL mW (Form SD)

Additional Info

Add to compare

Type CHEMOPAL mW (Form SD)

Chemical Hose (with steel helix)

Chemical hose CHEMOPAL for alkalis, acids, acetates, aldehydes, amines, esters, ethers and ketones.
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +90° C). Steaming out for cleaning and sterilisation permissible up to +150° C / max. 30 min (open ends).
Meets EN 12115.

DN 25 to DN 150

Chemical hose CHEMOPAL for alkalis, acids, acetates, aldehydes, amines, esters, ethers and ketones.
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +90° C). Steaming out for cleaning and sterilisation permissible up to +150° C / max. 30 min (open ends).
Meets EN 12115.

90

0

Chemical Hose (without / with helix)

Chemical hose TECNOPAL for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +100° C. Steaming out for cleaning and sterilisation up to +150° C / max. 30 minutes (open ends).
Meets EN 12115.

DN 13 to DN 150

Chemical hose TECNOPAL for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +100° C. Steaming out for cleaning and sterilisation up to +150° C / max. 30 minutes (open ends).
Meets EN 12115.

91

0

Type TECNOPAL oW (Form D)

TECNOPAL oW (Form D)

Additional Info

Add to compare

Type TECNOPAL oW (Form D)

Chemical Hose (without steel helix)

Chemical hose TECNOPAL for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +100° C. Steaming out for cleaning and sterilisation up to +150° C / max. 30 minutes (open ends).
Meets EN 12115.

DN 13 to DN 50

Chemical hose TECNOPAL for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +100° C. Steaming out for cleaning and sterilisation up to +150° C / max. 30 minutes (open ends).
Meets EN 12115.

92

0

Type TECNOPAL mW (Form SD)

TECNOPAL mW (Form SD)

Additional Info

Add to compare

Type TECNOPAL mW (Form SD)

Chemical Hose (with steel helix)

Chemical hose TECNOPAL for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +100° C. Steaming out for cleaning and sterilisation up to +150° C / max. 30 minutes (open ends).
Meets EN 12115.

DN 25 to DN 150

Chemical hose TECNOPAL for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).
Not suitable for aliphatic, aromatic, halogenated hydrocarbons and their derivates.
Temperature range (depending on medium) -40° bis +100° C. Steaming out for cleaning and sterilisation up to +150° C / max. 30 minutes (open ends).
Meets EN 12115.

93

0

Solvent Hose (without / with helix)

Solvent hose SOLVAPAL for most solvents, paints (also waterbased), water laquer, petroleum products, alcohols, alede hydes, esters and ketones. In short term operation also suitable for aromatic und chlorinated hydrocarbons.
Temperature range -20° bis +80° C, short term up to +100° C.
Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

DN 19 to DN 150

Solvent hose SOLVAPAL for most solvents, paints (also waterbased), water laquer, petroleum products, alcohols, alede hydes, esters and ketones. In short term operation also suitable for aromatic und chlorinated hydrocarbons.
Temperature range -20° bis +80° C, short term up to +100° C.
Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

94

0

Type SOLVAPAL oW (Form D)

SOLVAPAL oW (Form D)

Additional Info

Add to compare

Type SOLVAPAL oW (Form D)

Solvent Hose (without steel helix)

Solvent hose SOLVAPAL for most solvents, paints (also waterbased), water laquer, petroleum products, alcohols, alede hydes, esters and ketones. In short term operation also suitable for aromatic und chlorinated hydrocarbons.
Temperature range -20° bis +80° C, short term up to +100° C.
Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

DN 19 to DN 32

Solvent hose SOLVAPAL for most solvents, paints (also waterbased), water laquer, petroleum products, alcohols, alede hydes, esters and ketones. In short term operation also suitable for aromatic und chlorinated hydrocarbons.
Temperature range -20° bis +80° C, short term up to +100° C.
Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

95

0

Type SOLVAPAL mW (Form SD)

SOLVAPAL mW (Form SD)

Additional Info

Add to compare

Type SOLVAPAL mW (Form SD)

Solvent Hose (with steel helix)

Solvent hose SOLVAPAL for most solvents, paints (also waterbased), water laquer, petroleum products, alcohols, alede hydes, esters and ketones. In short term operation also suitable for aromatic und chlorinated hydrocarbons.
Temperature range -20° bis +80° C, short term up to +100° C.
Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

DN 25 to DN 150

Solvent hose SOLVAPAL for most solvents, paints (also waterbased), water laquer, petroleum products, alcohols, alede hydes, esters and ketones. In short term operation also suitable for aromatic und chlorinated hydrocarbons.
Temperature range -20° bis +80° C, short term up to +100° C.
Steaming out for cleaning and sterilisation permissible up to +130° C, max. 30 minutes (open ends).
Meets EN 12115.

96

0

Liquid Petroleum Gas Hose according to EN 1762 (without steel helix)

BUTAPAL liquid petroleum gas hose to EN 1762. For propane, butane and their mixtures to EN 589. As the hose lining is resistant to diffusion the hose is also suitable for natural gas.
Not suitable for ammonia.
Rugged and long-lasting construction with low tensile braids. Burst pressure >100 bar.
Temperature range -40° C up to +70° C (Special LT type down to -50° C).
Approved by DVGW, approval No. DG-4621 AU 0049.

DN 10 to DN 100

BUTAPAL liquid petroleum gas hose to EN 1762. For propane, butane and their mixtures to EN 589. As the hose lining is resistant to diffusion the hose is also suitable for natural gas.
Not suitable for ammonia.
Rugged and long-lasting construction with low tensile braids. Burst pressure >100 bar.
Temperature range -40° C up to +70° C (Special LT type down to -50° C).
Approved by DVGW, approval No. DG-4621 AU 0049.

Product Name	Type BUTAPAL
Short Description	Liquid Petroleum Gas Hose according to EN 1762 (without steel helix)
Description	BUTAPAL liquid petroleum gas hose to EN 1762. For propane, butane and their mixtures to EN 589. As the hose lining is resistant to diffusion the hose is also suitable for natural gas. Not suitable for ammonia. Rugged and long-lasting construction with low tensile braids. Burst pressure >100 bar. Temperature range -40° C up to +70° C (Special LT type down to -50° C). Approved by DVGW, approval No. DG-4621 AU 0049.
Application	Highly flexible reel hose for supplies to domestic and industrial storage tanks, as pump hose for vehicle refuelling, for bulk loading and unloading from rail tankers, road tankers and ships. For special suction / pressure operation needs the type BUTAPAL mW with stainless steel helix is available on request.
Comment	Electrical conductivity: 'OHM'-Type according to EN 1762. Electrical resistance R <10⁶ Ohm, measured in between hose end fittings , <10⁹ OHM from lining to cover, through the hose wall. Suitable for use in EX-Zones 0, 1 and 2. For the hose assembling, the copper strands do not have to be connected to the fittings. At customerʹs request the copper strands incorporated in the hose can be connected to the hose fittings with resulting electrical resistance R <10² Ohm ('M'-type according to EN 1762). Assembling and testing: For liquid petroleium gas hoses only suitable safety fittings according to EN 14422 or EN 14424 must be used which can be mounted tightly, see examples below. According to EN 1762, hose assembling must include a mandatory pressure and conductivity test.
Lining	Nitrile rubber (NBR), black, smooth, seamless, electrically conductive, diffusion resistant
Reinforcements	Textile braids with two crossed tinned copper strands
Cover	Chloroprene (CR), black, electrically conductive, flame and abrasion resistant, ozone-, UV- and ageing-resistant
Marking	Orange coloured spiral and abrasion resistant continuous embossing. Please note: Marking of BUTAPAL 10 with longitudinal orange stripe.
Marking Sample	ELAFLEX BUTAPAL 50 · EN 1762 · D · FLÜSSIGGAS · L.P.GAS · TEMPERATUR -40° C +70° C · DVGW – DG-4621 AU 0049 · M · Ω · PN 25 / WP 350 PSI · · CONTITECH · MADE IN GERMANY · 2Q-15
Size	DN 10 to DN 100
Product Sheet	Page PAL 15-16

Tech	Technically pure
Aq	Aqueous solution
Sat	Saturated solution

Configurator Hose Assemblies

Application Group

Medium

Media Search

Annotation to the Resistance Chart (Elaflex und PAL Hoses)

Media Search Composite Hose

Annotation to the Resistance Chart (Composite Hose)

Ratings

Abreviations

Seals

Material Liner

Standards

Hose

Reset all

BU	Butyl (Isobutyl isoprene)
NI	Nitrile (Buna-N, NBR)
VI	Viton® (Type A)
LT	Low temperature nitrile

Configurator Hose Assemblies

Selection Guide (Filter Products)

Annotation to the Resistance Chart (Elaflex und PAL Hoses)

Annotation to the Resistance Chart (Composite Hose)

Ratings

Abreviations

Seals