ELAFLEX Configurator Hose Assemblies

Select: Hose Type

Product Name	Slimline
Description	Petrol pump hoses according to EN 1360 and EN 13483. For gasoline and diesel fuels. Lining: NBR

Hose Type

Type Slimline 'SL'

Petrol Pump Hoses
black or coloured
Size: DN 16 to DN 21

Additional Info

Select to compare

Type Slimline 'SL LT'

Petrol Pump Hoses
- Low Temperature -,
black or coloured
Size: DN 16 to DN 25

Additional Info

Select to compare

Type Slimline 'BIO'

Petrol Pump Hoses
for gasoline and diesel fuels,
black or coloured
Size: DN 16 to DN 25

Additional Info

Select to compare

Type COAX

COAX hose assemblies for DN 21/8 NR
for dispensers with active vapour recovery,
black or coloured
Size: DN 21

Additional Info

Product Name	Type COAX
Part Number	COAX
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Certificates	DNV • GL - type examination certificate for pump hoses DN 21 for vapeur recovery fuel dispensing systems to EN 13483.
Size	DN 21
Product Sheet	GR 11
PDF Certificates	DNV • GL - type examination certificate for pump hoses

Select to compare

Type COAX LT

COAX hose assemblies for DN 21/8 NR
for dispensers with active vapour recovery
- Low Temperature -,
black or coloured
Size: DN 21

Additional Info

Product Name	Type COAX LT
Part Number	COAX LT
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery - Low Temperature -, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Certificates	DNV • GL - type examination certificate for pump hoses DN 21 for vapeur recovery fuel dispensing systems to EN 13483.
Size	DN 21
Product Sheet	GR 11
PDF Certificates	DNV • GL - type examination certificate for pump hoses

Select to compare

Type Slimline 'SL SF'

Petrol Pump Hoses
- Sulpur Free -,
black or coloured
Size: DN 16 to DN 21

Additional Info

Select to compare

Type Slimline 'SL SF LT'

Petrol Pump Hoses
- Low Temperature, Sulpur Free -,
black or coloured
Size: DN 16 to DN 21

Additional Info

Select to compare

Type COAX SF

COAX hose assemblies for DN 21/8 NR
for dispensers with active vapour recovery,
- Sulpur Free -,
black or coloured
Size: DN 21

Additional Info

Product Name	Type COAX SF
Part Number	COAX SF
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, - Sulpur Free -, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Application	For the operation in particularly cold regions (e.g. Scandinavia), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Comment	Refineries and Oil companies spend considerable effort in fulfilling the maximum allowed sulphur content of 10 mg/kg (corresponding 10 ppm) of the EN 228 and EN 590 fuel standards.To support these endeavours, Elaflex introduced a new special type of hose where rubber compounds are free of sulphur: Type Slimline 'SL SF'.• Tests of fuel samples verified that the sulphur content of the fuel is not increased, even if the medium remains for a long time within the hose. • It fulfills all requirements of the relevant hose standards. Properties are equally good or even better than those of standard Slimline hoses.
Certificates	DNV • GL - type examination certificate for pump hoses DN 21 for vapeur recovery fuel dispensing systems to EN 13483.
Size	DN 21
Product Sheet	GR 11
PDF Certificates	DNV • GL - type examination certificate for pump hoses

Select to compare

Type COAX SF LT

COAX hose assemblies for DN 21/8 NR
for dispensers with active vapour recovery,
- Low Temperature, Sulpur Free -,
black or coloured
Size: DN 21

Additional Info

Product Name	Type COAX SF LT
Part Number	COAX SF LT
Short Description	COAX hose assemblies for DN 21/8 NR for dispensers with active vapour recovery, - Low Temperature, Sulpur Free -, black or coloured
Description	PETROL PUMP HOSE (outside) TYPE SL 21: Quality petrol pump hose 'CONTI-SLIMLINE' DN 21-PN 16, OD , 31 mm, smooth surface, suitable for retraction devices up to min. ø 150 mm. Lining: NBR, electrically dissipative. Two textile reinforcements with interwoven conductivity strands. Cover: chlorinated synthetic rubber, resistant to light cracks. Available in black or coloured (blue, green, red, yellow) with smooth, colour stable surface. With continuous and permanent laser marking. Meet all requirements of EN 13483 (EN 1360). Also suitable for fuels with ethanol content up to E 85. HOSE COUPLINGS (factory assembled) Non-reusable safety couplings DN 21-PN 16 aluminium, swivel nut with standard thread M 34 x 1,5 of stainless steel, o-rings of Viton (FKM). Nozzle side: easy rotating swivel, with spiral spring supported lip seal ED 077 of LT (Low Temperature) flexible polyurethane (see Info 1.07). With 2 key faces width 41 mm. Pump side: swivel with six key faces width 36 mm and with O-ring EO 171 Vi. ANTI-KINKING SLEEVE On nozzle side anti-kinking sleeve KS 21 of low temperataure flexible polyurethane. With degassing holes. Non-reusable. COLOUR SLEEVE Short sleeve CS 21 with stable colours for grade identification or company colours. Made of polyurethane with smooth glossy surface in all known company colours. Retrofitting and disassembly are possible (see page GR 13). VAPOUR HOSE (inside) Vapour recovery hose DN 8 / PN 16 (OD ø 12 mm) of polyurethane (LT flexible). Resistant to petrol and ozone, low diffusion. Remains stable also with narrow bending radii, because of the steel reinforcements. With vapour hose tail DN 8 of PVDF black, with non reusable stainless steel clamps. Nozzle side with arresting device through locked vapour hose tail. Pump side swivel supported to avoid twisting through torsion. COMFORMITY TO WEIGHTS AND MEASURES / ELONGATION According to EN 13483 the volume increase of a new hose assembly is not allowed to be more than 2 % of the hose contents at 3 bar. 'CONTI-SLIMLINE' hoses meet this standard with sufficient safety tolerance due to their low-tensile textile reinforcements. According to the standard the elongation of the hose through swelling is allowed to be max. 4 %. During service with petrol 'CONTI-SLIMLINE' hoses elongate as follows: with leaded super petrol about 1 to 1,5 %, with unleaded super petrol about 1,5 to 2 %. PERMEABILITY According to EN 13483 the loss of petrol in a hose assembly is not allowed to be higher than 12 ml / m per day when using Liquid C. 'CONTI-SLIMLINE' hoses meet this standard. LOW TEMPERATURE BENDING FORCE The EN 13483 specifies that a new petrol pump hose must not require a higher bending force than 180 N when bending the hose at -30° C in a normed device with a radius of 75 mm at an 90° angle. 'CONTI-SLIMLINE' hoses DN 21 only require 70 to 100 N and meet the even higher requirements of the MPD manufacturers. For the operation in particularly cold regions (e.g. Scandinavia) we supply the LT type (Low Temperature), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Application	For the operation in particularly cold regions (e.g. Scandinavia), with a good retractability up to -40° C, dependent on the construction of the retraction device. It meets all requirements of the Low Temperature Type as described in EN 13483.
Comment	Refineries and Oil companies spend considerable effort in fulfilling the maximum allowed sulphur content of 10 mg/kg (corresponding 10 ppm) of the EN 228 and EN 590 fuel standards.To support these endeavours, Elaflex introduced a new special type of hose where rubber compounds are free of sulphur: Type Slimline 'SL SF'.• Tests of fuel samples verified that the sulphur content of the fuel is not increased, even if the medium remains for a long time within the hose. • It fulfills all requirements of the relevant hose standards. Properties are equally good or even better than those of standard Slimline hoses.
Size	DN 21
Product Sheet	GR 11

Select to compare

Type Slimline 16 AdBlue

Hose for AdBlue^{^®}Urea solution
for truck and passenger car dispensers,
black or blue
Size: DN 16

Additional Info

Select to compare

2Size (ID)

3Length (L1)

4Coupling Type 1

5Coupling Type 2

6Part No.

Click to Compare

Your choice:

Choose additional options
or click here to go on.

Product Name	Type Slimline 'SL SF LT'
Part Number	Slimline SL SF LT
Short Description	Petrol Pump Hoses - Low Temperature, Sulpur Free -, black or coloured
Description	Type Slimline 'SF LT': Special low temperature and sulphur-free type for use in cold climate regions. Good flexibility down to -40° Celsius.
Comment	Type Slimline 'SF': Special type 'sulphur-free'. Sulphur content of fuel does not increase, even if medium remains with the hose for a longer time, see Information 12.15. Due to their smooth cover and high flexibility, all Slimline hoses are well suitable for MPD hose retraction systems. Mandrel production, vulcanisation in a plastic cover. Long lasting premium quality, Made in Germany.
Lining	Nitrile rubber (NBR), black, seamlessly extruded, electrically dissipative, no discolouration
Reinforcements	Two low tensile textile braids with crossed, interwoven conductivity strands
Cover	Smooth, UV and ozone resistant, oil resistant, highly abrasion resistant. Material see chart.
Marking	With continuous, abrasion resistant embossed marking
Marking Sample	ELAFLEX SLIMLINE 16 SF LT · EN 1360 TYPE 1 · Ω · PN 16 · AS 2683 · · MADE IN GERMANY · - 09.16
Size	DN 16 to DN 21
Product Sheet	Page 111a,111b,111c
	Information 12.15

Product Name	Type Slimline 16 AdBlue
Part Number	Slimline AdBlue
Short Description	Hose for AdBlue^{^®}Urea solution for truck and passenger car dispensers, black or blue
Description	Quality dispensing hoses SLIMLINE 16 AdBlue for urea solution. Correspond to EN 1360.Dispensing hose DN 16 for the refilling of light and heavy vehicles with AdBlue^® (AUS 32, DEF, ARLA 32) urea solution to ISO 22241. The highly flexible hose is well suitable for MPD hose retraction systems and allows small bending radii and a good handling. In combination with the appropriate stainless steel hose couplings (pages 203/205), the plasticiser-free and leaching-resistant lining guarantees constant purity of the dispensed urea solution.
Comment	Alternative hose type for urea solution: Type EFL with fluoropolymer lining, DN 16 or 21; see catalogue page 113.
Lining	NBR, black, seamlessly extruded, electrically dissipative, plasticiser-free, leaching-resistant
Reinforcements	Low tensile textile braid
Cover	CR, black or blue, smooth, highly abrasion and ageing resistant
Marking	With continuous, abrasion resistant embossed marking
Marking Sample	SLIMLINE 16 AdBlue ∙ EN 1360:2013 ∙ Ω ∙ PN 16 ∙ ELAFLEX ∙ MADE IN GERMANY ∙ Batch – MM / JJ
Size	DN 16
Product Sheet	Page 111a-c
	Information 2.16